A Complete Guide on How to Login to Sagemcom Router

The Sagemcom router net interface is your control panel for your router it’s where all the configurations are saved and changed. To make changes to your network you will need to login to Sagemcom router.

how to login to sagemcom router

This article will show you the step-by-step procedures, so keep on reading and learn how to do it simply.

Prerequisites:
LAN-cable or via Wi-Fi
An internet browser, which you clearly have.

The following are the directions to link to the interface of a Sagemcom router for settings and diagnostics.

How to Login to Segacom Router

  1. Ensure You’re connected to a Sagemcom router
    To have the ability to attain the installation pages of your Sagemcom router, then you will want to be linked to its system.
    So start by connecting to the network, either through WiFi or through an ethernet cable.

    Tip: in case you don’t know the WiFi password to your Sagemcom router, you could always link to it using an ethernet cable, which will not require a password.
  1. Open your web browser and browse to 192.168.1.1
    Open your browser and type the router’s IP address into the address area. The most frequent IP for Sagemcom routers is 192.168.1.1 If that IP address doesn’t work, you can search the default Sagemcom IP address list for your particular version.

    Tip: Since you’re connected to a Sagemcom router, you may even use whatsmyrouterip.com to quickly locate the IP. It is the “Router Private IP”-value.
  1. Enter the username and password for your Sagemcom router
    In the username and password field, enter your current username and password and then press enter signal in.

Check out our latest post here: Complete Instructions on How to Install Audacity for Mac

Default Login Credentials for Sagemcom

If you’re not sure about the username/password you’re able to take a look at the default Sagemcom credentials to learn what the defaults are, and also the best way to reset to them. The credentials may also be published on the label on the rear of your router.

That is it! Now you can configure whatever you want on the device.

The way to configure your Sagemcom modem
You need to have the ability to change any settings which are 21, once you have logged into the Sagemcom admin port.
Be careful when you configure your router so you don’t break the system.

Tip: write down your current settings before changing anything so that you can revert it off of trouble.

Imagine in my Sagemcom router or network stops functioning after a configuration change. In the event you by mistake create some change that breaks your Sagemcom home network, you could always go back to zero by following the generic 30 30 30 hard reset trick.

This is usually the last resort, and if you still have access to this Sagemcom port you can always login to try and revert the settings first (This of course presumes you wrote down the initial value before changing it).

How to Change Existing Wireless Settings on Sagemcom

  • Open an internet browser.
  • Type http://home or http://192.168.2.1 from the address bar, then press Enter on your keyboard.
  • When prompted, enter the Connection Hub username (the default is admin).
  • Input the Link Hub password (the default is admin).
  • Click OK.
  • Click Wireless.
  • To change the network name (SSID), delete the current SSID.
  • Enter a new domain.
  • To change the network password, delete the password.
  • Enter a new password.
  • Scroll to and click Save to upgrade your wireless settings.

Conclusion

I hope you are now able to setup or configure your Sagemcom router. Regardless of the modem you are using, the proedures are just the same. So, it applies to all Sagemcom routers.

If in case you still need assistance, do not hesitate to leave us a comment. You may also directly contact us using the contact form.

Complete Instructions on How to Install Audacity for Mac

How to Install Audacity for Mac

Are you looking for a good audio editor for your Mac? If you haven’t found out one, this article is for you.

We all know that Mac computers are more restrictive and exclusive than other OS. Thus, you’ve probably noticed that not all applications for Windows are available for you. So, once you search for a program, like an audio editing tool, you might have limited and lesser choice.

But don’t worry yet because Audacity got your back. This audio editor works flawlessly not only on Windows but also on Mac computers. So, to know how to install Audacity, refer to the next section. 

audacity for mac

How to Setup Audacity for Mac

Audacity contains different features which are all useful when it comes to the editing process. Aside from enhancing your audio, it has an efficient recorder that allows you to capture sounds. You may also download plugins for the application. To highlight, Audacity is an open-source program so it’s sort of difficult to manage. 

Here are the steps to install audacity on your Mac computer.

  1. First off, go to the official website of the program and select the installer for Mac OS/ Mac OS X. This will allow you to download Audacity for Mac
  2. Next, locate the file that you have downloaded and run such on your computer.
  3. Wait until the file has been completely installed then agree to the terms and conditions.
  4. Follow the on-screen instructions to finalize the process.

Once you have installed Audacity, go back to your home screen and click on the application’s icon to launch it. If you want to know if you’re running the latest version, simply click on Help Menu and choose About Audacity from the options. This will provide you with the information regarding your program such as the version. 

And that’s it! By following the steps above, you’ll be able to install Audacity on your computer. If you have questions or queries, please leave a comment at the box below. 

We hope that you have learned something from the article. Stand by for other future educational posts – the staff.

“One good thing about music, when it hits you, you feel no pain.”

― Bob Marley